Hoppa till innehåll
Free shipping on orders over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Why your reading is wrong when you read a scale with an ordinary loupe, and how telecentric optics remove the errorWhat You Can’t See Around the Corner Costs More Than What You Dismantle to Get AccessSee the solder joint and surface defect on a screen instead of through a magnifier, and document it right awayReflections on shiny metal surfaces cause defects to be missed, but a polarizing filter removes themA 0.1 mm groove is visible in the image but can’t be measured: how to get both sharpness and depth from the same microscopeMeasure directly in the image: no more guessing the magnification or fighting reflections during microscopic inspectionSee inside the machine without taking it apart: a camera in the tip gives a sharper image than fiber opticsReflections hide the flaw: how to see scratches, burrs and solder defects on shiny surfacesSpotting the fault in the pipe before you tear up the floor saves more than the repair itselfShiny metal surfaces hide scratches and cracks until the reflections disappear from the imageVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Why your reading is wrong when you read a scale with an ordinary loupe, and how telecentric optics remove the errorWhat You Can’t See Around the Corner Costs More Than What You Dismantle to Get AccessSee the solder joint and surface defect on a screen instead of through a magnifier, and document it right awayReflections on shiny metal surfaces cause defects to be missed, but a polarizing filter removes themA 0.1 mm groove is visible in the image but can’t be measured: how to get both sharpness and depth from the same microscopeMeasure directly in the image: no more guessing the magnification or fighting reflections during microscopic inspectionSee inside the machine without taking it apart: a camera in the tip gives a sharper image than fiber opticsReflections hide the flaw: how to see scratches, burrs and solder defects on shiny surfacesSpotting the fault in the pipe before you tear up the floor saves more than the repair itselfShiny metal surfaces hide scratches and cracks until the reflections disappear from the image

Articulating Inspection Camera TDR35SEN-3 with 270° Steerable Probe: When the Camera Needs to ”Look Backwards” Around a Bend to Inspect Hidden Surfaces

Published July 13, 2026 at 08:56

A maintenance technician is inspecting a gas turbine section via an 8 mm access port. The probe needs to enter, make a 90° bend, and then ARTICULATE UPWARDS to inspect the underside of the turbine blades. A standard fixed-direction probe can go IN, make the bend, but the camera will then look STRAIGHT ahead — NOT up towards the underside of the blades. Changing the probe’s angle would require pulling out the entire probe, rotating it, and reinserting it. Cumbersome.

With an articulating inspection camera probe, the operator can ROTATE THE CAMERA HEAD 270° via a handle controller WITHOUT moving the probe. The camera can look:

  • Forward (0°).
  • 90° up or down.
  • Backward (180°) — directly ”looking backwards” around the bend.
  • And all intermediate positions up to 270°.

This opens up inspection access to areas that would otherwise be blind spots. The TDR35SEN-3 is a 3-meter variant with a 270° steerable head for 22,300 SEK.

Articulation Mechanics

Steerable endoscope heads use wire actuation:

  1. The camera head is mounted on a flexible gimbal joint at the probe tip.
  2. Four CONTROL WIRES run the entire length of the probe — parallel to the video signal cable.
  3. At the handle controls, a JOYSTICK is connected to four WINCH mechanisms — one for each wire.
  4. When the operator tilts the joystick UPWARDS, one wire is pulled (tilting the camera head upwards) while the opposing wire is released.
  5. The same principle applies to left/right.

This wire-actuation mechanism is the same as that used in medical bronchoscopes and laparoscopes. Standard technology since the 1980s, yet still impressive in its mechanical integrity — thousands of wire-pull cycles without wearing out the probe’s flexible sheath.

270° Range in Practice

270° means the camera head can be rotated from 0° to 270° from the probe’s straight-ahead direction. This is MORE than 180° (straight back) but LESS than 360° (full circle).

In practice:

  • 0°: Straight ahead.
  • 90°: Straight up (or down depending on the joystick).
  • 180°: Straight back.
  • 270°: Angle between ”backward” and ”sideways”.

Full 360° articulation would require complex multi-joint mechanics (typically 3–4 separate gimbals in series). 270° can be achieved with a single gimbal and is sufficient for most inspection applications.

Applications Where Articulation Is Essential

Turbine inspection (aerospace, gas, steam): Compressor and turbine blades from side access. Wire actuation provides access to the underside of the blades without opening the turbine housing.

Engine cylinder inspection: Through spark plug holes, the camera can look up toward the cylinder head, and down toward the top of the piston.

Pipe inspection with T-junctions: At a T-junction, an articulating probe can select which branch to inspect.

Vehicle body inspection: Through rust holes, the camera can be guided up into structural cavities.

Electronics inspection in densely packed cabinets: Through access panels, the camera can be directed toward specific PCB components.

Building diagnostics: Through insulation inspection holes, the camera can be navigated through wall cavities.

Museum and archaeology work: Inside antique artifacts (e.g., sarcophagi without opening them).

Artikulerande inspektionskamera TDR35SEN-3 med 270° styrbart huvud, 3m sond

5.5 mm Probe with 3 m Range

The 5.5 mm probe diameter fits into:

  • Standard spark plug holes.
  • Most service access ports on engines.
  • 6 mm boreholes (for building inspection).
  • Standard endoscope ports on industrial equipment.

A 3 m range is typical for medium-sized industrial inspections. For longer reaches (10–30 m), specialized models are required (such as the HDV650 I wrote about earlier — 10 m; or 30–40 m pipe inspection cameras).

Detachable 3.5″ Screen

The TFT-LCD screen can be detached from the handle. This enables:

  • The screen can be hung around the operator’s chest with a strap (included).
  • A second person can hold the screen while the first person navigates the probe.
  • The screen can be mounted on a tripod in confined workspaces.

A built-in Li-Po battery in the screen provides 3–5 hours of cord-free runtime. A separate battery is housed in the handle for probe illumination.

Video Recording + 3× Zoom

A micro-SD card (up to 32 GB) is housed in the screen. Video recording is saved in standard MP4 format.

3× DIGITAL zoom (not optical) — enlarges the image via electronic processing. Digital zoom reduces image quality, but is practical for viewing fine details without moving the probe closer.

Three Included Accessories

The probe comes with three accessories that can be mounted onto the tip’s thread:

Hook: For retrieving and pulling out small objects (screws dropped into an engine, wires that need to be pulled forward).

Mirror: 45° mirror providing a side view when the probe head cannot be articulated. Also serves as a backup in case of articulation mechanism failure.

Magnet: Captures magnetic objects (screws, nuts) in hard-to-reach locations.

These accessories transform the inspection endoscope into a MULTI-TOOL — not just for ”seeing”, but also for ”grabbing” and ”retrieving”.

IP67 Waterproof Rating

The probe’s IP67 rating means it can be submerged in water to a depth of 1 m for 30 minutes. Practical for:

  • Pipe inspection in water-filled lines.
  • Engines with coolant spills.
  • Outdoor work in rainy conditions.
  • Quick rinsing after use.

The handle and screen do NOT share this high IP rating — only the probe assembly does. In water-filled applications, the handle must be kept above the water level.

What You Get for Your Money

TDR35SEN-3 articulating inspection camera with 270° steerable camera head, 5.5 mm probe diameter × 3 m probe length, IP67 waterproof probe, 3.5″ TFT-LCD detachable screen with built-in Li-Po battery, video recording to micro-SD (up to 32 GB), 3× digital zoom, adjustable LED lighting, wire-actuation steering system, rechargeable battery, three included accessories (hook, mirror, magnet), hard carrying case. 22,300 SEK.

The standard tool for professional industrial inspection where articulation is required — turbines, engines, branching pipe networks, electronics cabinets, building diagnostics. The higher price compared to standard fixed-direction endoscopes (typically 3,000–10,000 SEK) is immediately justified in applications where probe directional flexibility is critical. For simple straight-ahead inspections, basic models are sufficient.

Read more: Articulating inspection camera TDR35SEN-3 in the shop →

More news

All news